Shimano -Shift inner derailleur cable, 3000mm, for cargo tandems – Y60030014

Shimano ’ Shift Inner Cable Y60030014 is an inner gear cable specially designed for tandems and bicycles requiring a long cable. At 3,000 mm in length, it provides ample slack for long frames and complex cable routing.

Made from SUS stainless steel, this Shimano derailleur cable, with a diameter of 1.2 mm, offers good resistance to corrosion and wear. Its 3-metre length makes it particularly suitable for routing front or rear derailleur cables on a tandem bike without the need for multiple cables or an extension.

Part number Y60030014 is part of the Shimano range of inner gear cables and is officially designated as ‘Stainless Steel Shifting Inner Cable for Tandem’. It is also suitable for various bikes fitted with a mechanical drivetrain requiring an extra-long cable, including certain cargo bikes, recumbent bikes or specialised set-ups.

Key features of the Shimano Y60030014 cable

• Shimano derailleur inner cable.
• Specially designed for tandems.
• Extra-long length of 3000 mm.
• Diameter: 1.2 mm.
• Made from SUS stainless steel.
• Good corrosion resistance.
• Surface designed to ensure smooth operation within the sheath.
• Cable end cap included.
• Suitable for mechanical drivetrains on road, mountain and touring bikes.
• May also be suitable for certain cargo bikes, recumbent bikes or set-ups with long cable runs.
• Manufacturer’s reference: Y60030014.
• EAN: 4524667103523.

An extra-long cable, ideal for tandems

On a standard bike, gear cables are usually around 2 metres long. On a tandem, the distance between the shifters and the derailleurs can be significantly greater due to the length of the frame and the drivetrain configuration.

At 3 metres, the Y60030014 cable Shimano provides the length needed to route the cable fully, whilst leaving enough slack to make adjustments and cut the cable cleanly after installation.

This extra length is also useful for bikes with complex internal cable routing or for certain specialised configurations. Specialist retailers therefore recommend it for tandems, recumbent bikes, two-wheeled cargo bikes and three-wheeled cargo bikes.

Stainless steel: strength and durability

The Y60030014 cable is made from stainless steel, which gives it better corrosion resistance than a standard steel cable. This feature is particularly beneficial for a component fitted inside a cable housing, where moisture can gradually cause corrosion.

Shimano It also features a low-friction design, whilst the SUS construction provides protection against rust. A clean, correctly fitted cable therefore helps to ensure more precise and consistent derailleur control.

Compatibility and use

Shimano ’s Y60030014 cable is designed for mechanical gear-shifting systems. It can be used with compatible Shimano drivetrains, as well as with various road, mountain bike and trekking set-ups.

Its length of 3000 mm is particularly suitable for:

• tandems;
• recumbent bikes;
• cargo bikes and two-wheeled cargo bikes;
• tricycles;
• certain road bikes or mountain bikes with long internal cable routing;
• set-ups requiring a longer-than-normal cable length.

Compatibility, however, depends on the type of shifter and derailleur used. The 1.2 mm diameter corresponds to the standard for inner gear cables Shimano.

Shimano Y60030014 is a particularly useful cable whenever a standard derailleur cable is too short. Its 3-metre length is its main advantage and avoids the need for makeshift solutions or splices on tandem drivetrains.

The use of stainless steel is also beneficial for a bike used regularly outdoors. It minimises corrosion-related problems and helps to maintain smooth drivetrain operation over time.

When fitting, we recommend replacing the outer casing at the same time if it is worn, contaminated or heavily marked. A new cable in a casing that is in poor condition will not allow for optimal performance.

Another tip: only cut the cable after you have adjusted the derailleur and checked its full travel. The 3,000 mm length provides a comfortable margin, but it is best to keep enough length to allow for handlebar movement and future adjustments.

Technical specifications